Hawk Performance Ceramic Rear Brake Pads 13 Mehndi ideas mehndi, mehndi simple, mehndi designs. Hawk understands the needs of today's ceramic brake pad users and has specifically formulated our composite material to meet and beat the stringent low noise, ultra low dust performance standards they have set. Engineered to reduce brake NVH (Noise, Vibration and Harshness), Performance Ceramic is a premium disc brake pad that delivers excellent performance mile after mile. Providing a linear friction profile that allows your vehicle's ABS system to operate most effectively, our unique compound has the advantage of never sacrificing power to achieve traditional ceramic pad attributes. With Hawk's PC, you can expect reduced brake pad wear, longer rotor life, and our quietest ride ever. Features: STREET USE ONLY Extremely quiet Ultra low dust Improved stopping power Gentle on rotors for extended pad life Stable friction output All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron Metal rotors. 38C 343C operating temperature range 38C 232C optimal temperature range Vehicle Fitment: To ensure correct compatibility we always recommend comparing your existing brake pads to the pad shape diagram provided above. Vehicle fitment provided is to be used as a guide only and may not suit your vehicle. 2005 2014 Ford Mustang GT S197 Important Installation and Brake Bedding Procedure: STREET Installation instructions should be followed in accordance with the application? specific brake pad installation instructions provided by the vehicle manufacturer. Brake Pad Installation Procedure: Install brake pads properly. Be sure pads are securely positioned in the caliper. Check Brake Fluid. Flush and replace, as needed. Check all hydraulic parts for excess wear and tear. Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed. If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130? grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid. Inspect calipers for freedom of movement. Lubricate where necessary. Street Brake Pad Burnishing Bedding? In Instructions: To break in the new components, make 6 to 10 stops from approximately 30 to 35 MPH applying moderate pressure. Make an additional 2 to 3 hard stops from approximately 40 to 45 MPH. DO NOT DRAG BRAKES! Allow 15 minutes for brake system to cool down. Your brakes are now ready for use and can be driven normally. MOTORSPORTS Installation instructions should be followed in accordance with the application? specific brake pad installation instructions provided by the vehicle manufacturer. Brake Pad Installation Procedure : Install brake pads properly. Be sure pads are securely positioned in the caliper. Check Brake Fluid. Flush and replace, as needed. Check all hydraulic parts for excess wear and tear. Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed. If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130? grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid. Inspect calipers for freedom of movement. Lubricate where necessary. Motorsports Brake Pad Burnishing Bedding? In Instructions: After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times. At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times. At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion. Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch. If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal. IMPORTANT REMINDERS WHEN BURNISHING BEDDING BRAKE PADS: Do not attempt to use badly worn or damaged rotors with new brake pads. Do not drag brakes while car is moving during break? in procedure. Do not engage pedal while car is stopped at any time following the break? in procedure. Upon completing the procedure, allow the brake system to completely cool before racing. Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds. Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads. Some forms of racing dont allow time for the proper break? in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible